Rear Wheel Bearing Replacement - 924, early 944
Parts needed: Rear Wheel Bearing Kit Stub Axel Nut/Rear Wheel Bearing Nut Moly Grease Procedure:
Lift rear or entire vehicle SAFELY!
Release handbrake
Remove the rear wheels.
Rem |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Rod Bearing Replacement
Discussion:
This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car. With some modifications it may also be applied to normally aspirated 944 |
Rear Wheel Bearing Diagnosis
Diagnosis : Name that tune... ' wuh wuh wuh wuh ', as you go around a corner? Rhythmic rubbing sounds from the rear of the car, especially during cornering, is usual |
Front Shock Replacement
Author: Skip
The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert tha |
Front Torsion Bars (65-89)
Author: Skip
Jack up the car and remove the front wheels. Remove the tow hooks that secure the front of the A-arm and torsion bars if your car is so equipped. Use the 17mm socket on two bolts an |
Accusump Installation
Author: Skip
I know of few topics that elicit such dismissive and strongly held opinions as that of how to eliminate the cause of #2 rod bearing failure in 944 engines. Some builders claim that |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Brakes, front - 924S, 944, 944S
Author: Skip
Parts:
Rotors - Sebro Slotted ( OE Zimmerman or , gas-slotted and cross-drilled also available)
Pads - ( 944.351.951.02 E Pagid or Jurid , Mintex and KFP Magnum also av |
Brey-Krause Strut Brace Installation - 944
Author: Skip
Installation :
Open hood to gain access to the strut bearing mounting nuts.
There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Oil Cooling, Auxiliary
KISS ENGINEERING OIL COOLER KITS
944/944 TURBO
TEST DATA AND INFORMATION
COOLER &n |
Torque Tube Rebuild
To recondition a Torque tube:
Order 4 of 6006ZB C4 Bearings, they are an odd size and can be hard to locate (at least in New Zealand) so get them first.
Remove the Torque tube from |
Front Shock Replacement (65-89)
Author: Skip The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert th |
Front Torsion Bars
Author: Skip
Jack up the car and remove the front wheels. Remove the tow hooks that secure the front of the A-arm and torsion bars if your car is so equipped. Use the 17mm socket on two bolts an |
6 - Speed and Horsepower
The title of this month's article consists of two words dear to every racer's heart. This month, we do some "back of the envelope" calculations to investigate the basic physics of speed and horsepowe |
Tarett Engineering Rear Sway Bar Installation Instructions
REAR SWAY BAR ASSEMBLY INSTRUCTIONS 1) Tarett Engineering rear sway bars are designed to mount directly to the factory mounting brackets on 1965-89 911’s, 912’s & 930’s. Any cars without factory m |
