Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Koni Strut Conversion - 8641-1414S for late 944, 968
Author: Skip
Koni sealed strut insert conversion (8641-1414S)
Description
Image
Parts : Koni 8641-1414S Sport Struts - all conversion and instructions parts included.
|
Odometer Gear Replacement - late 944
Author: Skip
Instructions :
Remove 9 screws holding front/back together:
Remove 4 screws holding speedometer in housing:
Gently pull off speedometer needle and remove 2 screws holdi |
Clock/Bulb Replacement, digital, Late 944 and 968
Author: Skip
To get access to the clock light, do the following:
Remove the two air direction slider knobs on the heater controls face plate (leave on the round knobs).
Very carefully |
AC Delete
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products ($129 plus shipping). The kit consists of the aluminum factory alternator mounting bracket for non-A/C 944’s and a 6 |
A-arm bushing modification (65-68 911/912)
Author: Skip Discussion: During various parts of my '66 912 restoration/rebuild/upgrade project, I've come up against the curse of old car restorers-parts! Yes, I know, Porsches are actually on |
Gate Shift Installation
Author: Skip
The following is a brief overview of the installation process for 901/915 transaxles. 901 users must obtain a 915 shift housing. Complete instructions are included with |
Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
AC Delete
Author: Skip
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products (Product Code: PP944.ACDEL.KIT1). The kit consists of the aluminum factory alternator mounting br |
Accusump Installation
Author: Skip
I know of few topics that elicit such dismissive and strongly held opinions as that of how to eliminate the cause of #2 rod bearing failure in 944 engines. Some builders claim that |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Alternator Replacement
Author: Skip
The alternator is located in the driver's side engine compartment, under the air-flow meter (AFM), in front of the Turbo unit, and on top of the A/C compressor looking down into |
Clutch Replacement - Part One
Author: Skip
The following account explains in detail the procedure of changing a clutch in a 944/951. It also contains a list of tools, chemicals, parts and the sources where to find them. The |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
Control Arm, Front - Info
Author: Skip
924 mid 82 and older - stamped steel - VW/Audi part# 477.407.153F (left & right)
924 mid 82 and later, 924S, 944 83-85.1 - stamped steel - VW/Audi part# 171.407.153D &nbs |
DME Chip Installation
Author: Skip
Location:
924S - located under the steering column - remove the four 8mm nuts holding it in.
85.5-91 944, 968 - located in the passenger-side foot well, behind the carp |
KLA Boxster Top Fix
Author: Skip
Boxster Lift Rod End Replacement Instructions:
Raise the tonneau cover to an upright position. This will be just before the top starts to pull back.
|
Motive Power Bleeder
Author: Skip
The Motive Products POWER BLEEDER TM works just like professional pressure bleeders -- at a fraction of the cost. With a POWER BLEEDER TM , one person can easily, safely, and |
