Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
Accusump Installation
Author: Skip
I know of few topics that elicit such dismissive and strongly held opinions as that of how to eliminate the cause of #2 rod bearing failure in 944 engines. Some builders claim that |
Brey-Krause Strut Brace Installation - 944
Author: Skip
Installation :
Open hood to gain access to the strut bearing mounting nuts.
There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner |
DME Chip Installation
Author: Skip
Location:
924S - located under the steering column - remove the four 8mm nuts holding it in.
85.5-91 944, 968 - located in the passenger-side foot well, behind the carp |
Rear Sway Bar Installation
This procedure is specifically for the installation of a 968 M030 Sway Bar but also applies to any 924/944/968 factory sway bar.
The best (easiest) way to remove or install the sway bar is with |
Camber Plate Installation (Paragon)
Author: Skip
Your new Racers Edge Camber Plates will bolt in without modification.
After jacking up your car and supporting it on jack stands, remove the wheel/t |
KLA Strut Brace Installation - 924S, 944, 968
944 STRUT BRACE INSTALL
1) Remove 4 nuts holding strut
assembly to the body.
2) Place bracket over studs with
bracket upright toward front of car.
|
Gate Shift Installation
Author: Skip
The following is a brief overview of the installation process for 901/915 transaxles. 901 users must obtain a 915 shift housing. Complete instructions are included with |
KLA Strut Brace Installation - 911
Author: Skip
Installation :
Remove front strut bolt and rear inner strut bolt.
Place bracket, long leg of bracket toward front of car, over holes and replace bolts.
Tighten to about |
KLA Strut Brace Installation - 964/993
Author: Skip KLA Strut Brace for 964/993 Installation: Remove 3 nuts holding strut assembly to the body. 2 nuts toward front of car. 1 rear/inner nut. Place bracket over studs with |
Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here . Determine where on the seat back the mount needs to be to have the 1½” tubing within ±20° from hori |
RennShift 901 and 915 Installation Instructions (911 and 914 cars)
|
KLA Strut Brace Installation - 968/944 S2/944 S
1) Remove 4 nuts holding strut
assembly to the body.
2) Place bracket over studs with
bracket upright toward rear of car.
3) Replace washers
and nuts.& |
Tarett Engineering Rear Sway Bar Installation Instructions
REAR SWAY BAR ASSEMBLY INSTRUCTIONS 1) Tarett Engineering rear sway bars are designed to mount directly to the factory mounting brackets on 1965-89 911’s, 912’s & 930’s. Any cars without factory m |
AC Delete
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products ($129 plus shipping). The kit consists of the aluminum factory alternator mounting bracket for non-A/C 944’s and a 6 |
Front Torsion Bars (65-89)
Author: Skip
Jack up the car and remove the front wheels. Remove the tow hooks that secure the front of the A-arm and torsion bars if your car is so equipped. Use the 17mm socket on two bolts an |
AC Delete
Author: Skip
I recently purchased the 944 A/C Delete kit from Jason Burkett at Paragon Products (Product Code: PP944.ACDEL.KIT1). The kit consists of the aluminum factory alternator mounting br |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Control Arm Bushing Upgrade - Weltmeister
Author: Skip
Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years. This bushing kit is a replacement for the original equipment rubb |
