Knowledge Base:  

You are here: Knowledge Base : Race
Page of 2
Brey-Krause Strut Brace Installation - 944
Author: Skip Installation : Open hood to gain access to the strut bearing mounting nuts. There are (4) 13mm. strut bearing mounting nuts per side. Remove the (2) front and (1) inner
KLA Strut Brace Installation - 924S, 944, 968
944 STRUT BRACE INSTALL 1) Remove 4 nuts holding strut assembly to the body. 2) Place bracket over studs with bracket upright toward front of car.
Pagid pads USED successfully at three major endurance races
Pagid pads USED successfully at three major endurance races   24 Hr Race Le Mans (France) Pagid’s stopping power and longevity pay of at the 2011 Le Mans 24h r
KLA Strut Brace Installation - 964/993
Author: Skip  KLA Strut Brace for 964/993 Installation: Remove 3 nuts holding strut assembly to the body.  2 nuts toward front of car.  1 rear/inner nut. Place bracket over studs with
Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here . Determine where on the seat back the mount needs to be to have the 1˝” tubing within ±20° from hori
KLA Strut Brace Installation - 968/944 S2/944 S
1) Remove 4 nuts holding strut assembly to the body. 2) Place bracket over studs with bracket upright toward rear of car. 3) Replace washers and nuts.&
KLA Strut Brace Installation - 911
Author: Skip Installation : Remove front strut bolt and rear inner strut bolt. Place bracket, long leg of bracket toward front of car, over holes and replace bolts. Tighten to about
Camber Plate Installation (Paragon)
Author: Skip   Your new Racers Edge Camber Plates will bolt in without modification.   After jacking up your car and supporting it on jack stands, remove the wheel/t
You know you're a racer when...
YOU KNOW YOU’RE A RACER WHEN: -You think the primary purpose of wings is to PREVENT flight. -You take your helmet along when you go buy new eyeglasses or check out cars (seats). -You feel
PAGID race pad mounting and bedding in
Author: Pagid PAGID race pad mounting and bedding in MOUNTING NEW PADS ON USED DISCS (rotors) We do not recommend using discs, which are pre
Front Shock Replacement
Author: Skip The 911, 914 and some 944’s featured a rebuildable front McPherson Strut. Instead of having to replace the entire strut unit, you will be able to merely replace the strut insert tha
Control Arm Bushing Upgrade - Weltmeister
Author: Skip Weltmeister has produced several aftermarket solutions to Porsche suspensions for many years.  This bushing kit is a replacement for the original equipment rubb
Control Arm, Front - Info
Author: Skip 924 mid 82 and older - stamped steel - VW/Audi part# 477.407.153F (left & right) 924 mid 82 and later, 924S, 944 83-85.1 - stamped steel - VW/Audi part# 171.407.153D &nbs
K&N Air Filter Facts
Author: Skip Why K&N Makes The World's Best Air Filters Facts You Should Know About Air Filters Paper vs K&N Stock Replacement Filters Washable and Reusable Beyo
Oil Cooling, Auxiliary
  KISS ENGINEERING OIL COOLER KITS 944/944 TURBO TEST DATA AND INFORMATION     COOLER           &n
Rear Wheel Bearing Replacement - late 944, 968
  Discussion :   This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944  with aluminum trailing arms (1985.5 & later)
Rod Bearing Replacement
  Discussion: This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car.   With some modifications it may also be applied to normally aspirated 944
Transaxle Fluid - Info
  The Basics: Friction Modifier (FM) is slippery stuff. The FM is in place to reduce LSD clutch chatter upon engagement. The amount needed is relative to the application and the age of
Transaxle Replacement
Removal :      You will need to place the car up on jack stands at least 20”. Make sure that it is secure! Remove the rear wheels and the axles. If you have never had the axles
3 - Basic Calculations
In the last two articles, we plunged right into some relatively complex issues, namely weight transfer and tyre adhesion. This month, we regroup and review some of the basic units and dimensions need