Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here . Determine where on the seat back the mount needs to be to have the 1˝” tubing within ±20° from hori |
Window Express Kit Installation
Window Express Kit Installation Instructions.
Author: Skip
Find the Window Express Right Here.
Introduction
Most modern |
Adjustable Ride Height Kit - Paragon
Items Included:
2x - Upper Spring Perch
2x - Koni Competition Bump Rubber
2x - Suspension Spring
2x - Aluminum Threaded Collar
2x - Lower Spring Perch
2x - O-ring |
Brakes, front - 924S, 944, 944S
Author: Skip
Parts:
Rotors - Sebro Slotted ( OE Zimmerman or , gas-slotted and cross-drilled also available)
Pads - ( 944.351.951.02 E Pagid or Jurid , Mintex and KFP Magnum also av |
Clutch Replacement - Part Two
Author: Skip
TRANSMISSION:
Remove shift boot lever (retaining clip at top )(Be careful of plastic cosmetic items, remove ashtray, two screws, lift center piece slightly & push out lea |
Clutch Slave Bleeder Valve Remote
Author: Skip
A couple of years ago, while running at NHIS, I had some difficulty getting good, clean downshifts into second gear without double clutching. While some would attribute this to poo |
DME Chip Installation
Author: Skip
Location:
924S - located under the steering column - remove the four 8mm nuts holding it in.
85.5-91 944, 968 - located in the passenger-side foot well, behind the carp |
Motive Power Bleeder
Author: Skip
The Motive Products POWER BLEEDER TM works just like professional pressure bleeders -- at a fraction of the cost. With a POWER BLEEDER TM , one person can easily, safely, and |
Porsche Option Codes
Author: Skip
Code
Description
009
3 speed sportomatic transmission
018
Sport steering wheel with elevated hub
020
Speedometer with 2 scales KP |
Sway Bar Calculations
Author: Skip
Provided by KLA Industries to answer the question of how the drop-link length affects the rate of a sway bar.
Here is the angle of the dangle formulas for calculating the ch |
Koni Strut Conversion - 8641-1414S for late 944, 968
Author: Skip
Koni sealed strut insert conversion (8641-1414S)
Description
Image
Parts : Koni 8641-1414S Sport Struts - all conversion and instructions parts included.
|
Rear Wheel Bearing Replacement - 924, early 944
Parts needed: Rear Wheel Bearing Kit Stub Axel Nut/Rear Wheel Bearing Nut Moly Grease Procedure:
Lift rear or entire vehicle SAFELY!
Release handbrake
Remove the rear wheels.
Rem |
Rear Wheel Bearing Replacement - late 944, 968
Discussion :
This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later) |
Rod Bearing Replacement
Discussion:
This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car. With some modifications it may also be applied to normally aspirated 944 |
Transaxle Replacement
Removal :
You will need to place the car up on jack stands at least 20”. Make sure that it is secure! Remove the rear wheels and the axles. If you have never had the axles |
K&N Air Filter Care
K&N Air Filter Care
Author: Skip
You Can Feel the Power in the Air!
1. PRE-CLEANING
Tap the element to dislodge any lodge embedded dirt, then gently brush with a soft bristle brush. (Note: If |
You know you're a racer when...
YOU KNOW YOU’RE A RACER WHEN:
-You think the primary purpose of wings is to PREVENT flight.
-You take your helmet along when you go buy new eyeglasses or check out cars
(seats).
-You feel |
2 - Keeping Your Tyres Stuck to the Ground
In last month's article, we explained the physics behind weight transfer. That is, we explained why braking shifts weight to the front of the car, accelerating shifts weight to the rear, an |
4 - There Is No Such Thing as Centrifugal Force
One often hears of "centrifugal force." This is the apparent force that throws you to the outside of a turn during cornering. If there is anything loose in the car, it will immediately slide to the r |
