Home > Quick Links > PAGID RACE PADS >

Pagid Race Pad Set - 8091

Pagid 8091

Our Price: $704.94

Product Code: 8091

Pagid Track Pads*:

Optional Accessories*:
Ate Super Gold RBF - liter - (SHIPS VIA GROUND) [Add $1.00]
Motul 600 RBF - 500ml - (SHIPS VIA GROUND) [Add $1.00]
No, Thanks

The 8091 pad shape is available in the newest Pagid Racing Compound RSC which is specifically formulated for Ceramic Rotors. Pagid is the only company producing a higher performance pad for ceramic rotors and Paragon Products is the leading distributor of the RSC pads.

We can send your choice of one liter of ATE Super Gold, or one 500ml of Motul RBF 600 Racing Fluid per set of Pagid Race or Sport pads. You may also choose no brake fluid at all.

Fits Front of:
- Camaro Z28 [Ceramic Brakes] 2015 -
- Corvette Brembo [Ceramic Brakes] 2009 -
- Corvette Brembo 6 piston [Non Ceramic] 2009 -
- Corvette C7 Z06 [Ceramic Brakes] 2015 -
- Ferrari 430 Challenge [Ceramic Brakes]
- Ferrari 430 Scuderia [Ceramic Brakes]
- Ferrari 458 Italia [Ceramic Brakes]
- Ferrari 599 GTB Fiorano [Ceramic Brakes]
- Ferrari for Several [Ceramic Brakes]
- McLaren MP4-12C [Ceramic Brakes] 2011 - 2014
- McLaren 570 S [Ceramic Brakes] 2015 -
- McLaren 650 S [Ceramic Brakes] 2014 -
- McLaren 650 LT [Ceramic Brakes] 2015 -
- Viper ACR [Ceramic Brakes] 2016

Brembo XA5.71.xx 6 Piston D85

  • PAGID Race Pad Fitting Instructions
    The new brake pads must move freely in their guides. If necessary remove paint from the contact faces. Delayed release and taper wear can occur if pads do not have enough clearance.

    The outer radius of the friction material must align with the brake disc’s outer radius. Especially with custom made uprights (knuckles) or custom made caliper mounting brackets very often pads do not align properly with the brake disc. It is advisable to place a note at the steering wheel to let the driver know new pads had been installed.

    Never lay hot pads up side down i.e. with the friction material onto the ground unless you throw them away anyway. Asphalt, rubber, oil etc. can melt into the friction material.

    PAGID Racing Brake Pad Bedding
    See brake pad bedding procedure

    If pads do not get bedded properly and / or used to hard right out of the box will likely lead to pad glazing. Pad glazing is a condition where the resins in the pad crystallize on both, the pad friction surface and the brake disc surface, resulting in poor stopping performance, brake judder and vibrations.

    Also rapidly escaping volatile elements and moisture from the resin would seek an immediate escape route out of the friction compound, creating small fissures that would lead shortly to cracking and chunking.

    Heat Cracks in Racing Brake Pads and Discs
    Multiple small heat cracks (hairline cracks) are normal and accepted for this type of use. Heat cracks on brake discs must not reach to the outer or inner edge of the disc.

  • Racing Brake Pads and Humidity
    When washing the car we recommend removing race brake pads or driving the car after washing and apply the brakes a few times in order to dry the brake pads. Water and even humidity of the air can slightly alter the friction behavior of racing brake pads. Some pro race teams use “storage” or “transport” pads and store the real race pads in a Zip-Lock bag until their next race.

  • Avoiding Brake Judder
    During bedding and shortly after, some judder is quite normal but should disappear after 5 to 10 laps. Changing back and forth between two incompatible friction materials (e.g. racing brake pads of different brands or street pads) can cause uneven build-up of pad material on the disc surface and can consequently lead to brake judder. Judder is the result of a thickness variation in pad buildup on the disc surface. Brake judder can be from a barely noticeable vibration to a violent judder. When you install Pagid race pads on top of a layer of an incompatible pad material, bedding might take much longer or in worst case won't work at all. It can also result in sub-optimal brake performance.

    Another reason for uneven pad transfer is called 'imprinting'. After coming to a complete stop with hot brakes (in the pits or after a spin), do not keep your foot on the brake pedal. The hot pads can leave a deposit behind that in turn again can cause judder and vibrations.

    Bigger vs Smaller Pad
    A larger friction surface will not improve stopping power. The amount of pressure applied, coefficient of friction and the disc diameter determine stopping force. A bigger pad does not apply more pressure, only the same pressure over a bigger area. The size of the pad matters in terms of heat capacity and wear rate. A larger pad will absorb more initial heat and has better wear characteristics.

    Pad Fade vs Brake Fluid Fade
    1.) pad fade
    When the temperature at the interface between the pad and the disc exceeds the thermal capacity of the pad, the pad loses friction capability mainly due to out-gassing of binder (matrix) materials in the pad compound. The brake pedal remains firm and solid but the car will not stop no matter how hard you push on the pedal. The first indication is a distinctive smell, a signal to back off. Solutions: better cooling, higher mass brake discs size and vane configuration or higher heat range pad compound.

    2.) fluid fade
    Boiling brake fluid develops gas bubbles in the calipers. The brake pedal becomes soft and pedal travel increases (because gas is compressible). One can still stop the car by pumping the pedal but efficient modulation is gone. This is a gradual process with advanced warning. The damaged fluid must be completely replaced. Correcting the problem is improved cooling and / or may only require new or higher grade racing brake fluid. The importance of keeping fresh brake fluid in the system and regular bleeding (before every session) cannot be overstressed.
    Back to Top

    Watch The Temps!
    It is highly recommended that brake temperatures are being monitored. Three temperature brake paints or similar products should be used. Ideally, the green paint (430°C / 806°F) should be completely oxidized (turns white), the orange paint (560°C / 1040°F) should be symmetrically beginning to oxidize and the red paint (610°C / 1130°F) should be un-touched or change only slightly.
    Caliper temperatures can be monitored with temperature strips.
    Checking the temperatures in the pit lane with a thermometer is a good way to oversee brake bias.

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

Quick Links
Alfa Romeo > Giulia 2.9 [952] Quadrifoglio [ceramic brakes] > front
BMW > Mini John Cooper Works [Brembo brakes] on request > undefined
Chevrolet > Camaro Z28 [Gen 5] [ceramic brakes] > front
Chevrolet > Corvette C6 Brembo 6 piston non ceramic > front
Chevrolet > Corvette C6 Brembo [ceramic brakes] > front
Chevrolet > Corvette C7 Z06 [ceramic brakes] > front
Ferrari > 430 Challenge [ceramic brakes] > front
Ferrari > 430 Scuderia [ceramic brakes] > front
Ferrari > 458 Italia [ceramic brakes] > front
Ferrari > 488 Challenge race car [ceramic brakes] > front
Ferrari > 599 GTB Fiorano > front
Ferrari > Several ceramic brakes CCM > front
Make > Model > undefined
McLaren > 765LT (brake pads in preparation) > undefined
McLaren > 570S [ceramic brakes] > front
McLaren > 650S / Spyder [ceramic brakes] > front
McLaren > 675LT [ceramic brakes] > front
McLaren > 765LT [ ceramic brakes] optional Senna Brake upgrade front > front
McLaren > MP4-12C [ceramic brakes] > front
Alfa Romeo > Giulia 2.9 [952] Quadrifoglio [ceramic brakes]
BMW > Mini John Cooper Works [Brembo brakes] on request
Chevrolet > Camaro Z28 [Gen 5] [ceramic brakes]
Chevrolet > Corvette C6 Brembo 6 piston non ceramic
Chevrolet > Corvette C6 Brembo [ceramic brakes]
Chevrolet > Corvette C7 Z06 [ceramic brakes]
Ferrari > 430 Challenge [ceramic brakes]
Ferrari > 430 Scuderia [ceramic brakes]
Ferrari > 458 Italia [ceramic brakes]
Ferrari > 488 Challenge race car [ceramic brakes]
Ferrari > 599 GTB Fiorano
Ferrari > Several ceramic brakes CCM
Make > Model
McLaren > 765LT (brake pads in preparation)
McLaren > 570S [ceramic brakes]
McLaren > 650S / Spyder [ceramic brakes]
McLaren > 675LT [ceramic brakes]
McLaren > 765LT [ ceramic brakes] optional Senna Brake upgrade front
McLaren > MP4-12C [ceramic brakes]
Alfa Romeo