Porsche 944 and 968 Brake Cooling Duct System

Home > 944 85.5 & Up (Late) and 968 > Brake > Brake Kits >

Brake Cooling Duct System

Our Price: $399.00

Product Code: BD-944NERP

Qty:

Description

Additional Information

Brake Cooling Duct System

Fits Porsche 944 and 968 with stock rotors and calipers not M030.

No matter what type of brake pad or brake fluid you use, you will dramatically increase the performance of your braking system by directly providing it with more cooling air. These kits feature non-breakable aluminum canisters, individually replaceable fiberglass scoops, and top quality hose material (where some kits take short cuts!). Are there less expensive kits on the market? You bet! Are there any that have better quality components? No way!

Click the Extended Information Tab for Installation Instructions.

Installation Instructions - 944

944 & 944S2 TURBO BACKING PLATE KIT INSTALLATION

The N.E.R.P. Aluminum brake backing plates are specifically designed for your vehicle. The backing plate has been designed to fit without any modifications to it. Now let’s get started.

Note: Turbo installation requires that the right front coolers be repositioned.

If you purchased the complete kit you should have the following components:

2 – ABS Intake scoops
1 – Section of 500°F Silicone Hose
2 – Black Anodized Aluminum backing plates
4 - 2 1/2"hose clamps
8 - 50# Black Nylon Tie wraps

Directions:

Properly lift and support the front end of the car, and remove the wheels.
Remove the brake calipers by removing the two bolts that secure the calipers to the strut and support them in a way not to damage the brake lines.
Remove the dust cap on the hub in order to gain access to the spindle clamp nut.
Remove the nut by loosening the screw that clamps it to the threaded spindle. You can now carefully remove the hub and bearings, being careful not to let the front bearing fall out.
If you have an existing backing-dust plate installed it needs to be removed. The new backing plate can then be installed with the inlet tube opening facing the top inside of the car.
Line up the bolt holes and bolt the backing plate to the spindle. Just snug the bolts at this time. Now carefully place the hub and rotor back onto the spindle and check the clearance between the backing plate and the brake rotor. The clearance can be adjusted by using shim washers behind the backing plate. Make sure that the backing plate does not rub on the rotor in the bearing seal location. When satisfied with the fit, the bolts can then be tightened to factory specs.
Install the hose between the scoop-duct and the backing plate securing at both ends with the supplied hose clamps.
Re-install the hub spindle clamp nut and adjust and tighten to factory recommendations.
Place the rotor back onto the hub.
Re-mount the brake calipers and tighten the bolts to factory specifications. You should also With the car still up on the jack stands, rotate the steering back and forth to check for any interference. If all checks fine, then re-attach the road wheels, lower the car and re-torque the lug nuts.

Average Customer Review: Average Customer Review: 5 of 5

5 of 5 Total Reviews: 1 Write a review.

0 of 0 people found the following review helpful:

	March 12, 2025
Reviewer: Todd Checkley from GOSHEN, IN United States

Was this review helpful to you?

Browse for more products in the same category as this item:

944 85.5 & Up (Late) and 968 > Brake > Brake Kits
944 85.5 & Up (Late) and 968 > Brake
944 85.5 & Up (Late) and 968

	Alternator - Rebuilt $423.00
	Pagid Race Pad Set - 8208 $458.52
	Main Bearing Set - standard $66.19
	Hollow Screw $9.46
	Head Gasket - Wide Fire Ring $118.55
	Odometer gear 20x30 $24.95
	Shift Pattern Insert - Stainless $39.95
	Ignition Coil $209.79
	Fuel Line Kit - Rennbay $110.00

Stay Updated

COMPANY

MY ACCOUNT

SHOPPING