Home > 944 85.5 & Up (Late) and 968 > Suspension >

Ball Joint Rebuild Kit - Track/Performance Kit with 19mm GCK Longer Pins
Ball Joint Rebuild Kit - Track/Performance Kit with 19mm GCK Longer Pins
 
Our Price: $285.00


Product Code: RB-944BK19GCK
Qty:

Description
 
Track/Performance Kit with 19mm GCK Longer Pins Ball Joint Rebuild Kit

Fits
- Porsche 944 1985.5-1991
- Porsche 944S/S2/Turbo All

Note: Will not fit 968 arms or new Porsche replacement arms made after 1998 as these arms are not rebuildable.
One Kit services both ball joints.
The pins are machined from a 4140/50 material called Accurloy. Accurloy was chosen because of it's ultra clean fine grain manufacturing process which ensures absolutely no carbon inclusions in the material. The pins are cut at the material delivered uniform hardness of Rockwell C 32 so there is no post heat treating process which could create material flaws in the finished parts.

The pin length is approximately 1.125" longer than the standard length pins. This allows for a corrected control arm geometry on cars lowered from 1.5" - 3" from the factory ride height. Factory ride height is measured with the control arm plane parallel to the ground (stock ball joints) at static suspension weight. To eliminate binding on cars on the lower end of the range a heavy enough spring rate should be used to keep the suspension travel from reaching the end of the ball joint pivot range.

The spindles must be machined at their clamping distance to be a true 19mm. This is done by first installing a standard 17mm ball pin to the spindle. With the pinch bolt torqued down you will need to measure the distance between the pinch gap. Remove the pin and shim the inside of the pinch to this measurement using a clamp to hold it in place. The 17mm bore must be aligned in a vertical mill, drilled undersized and reamed to 19mm.

Though the material we use is extremely tough it can be susceptible to fatigue fractures depending on track conditions and driving style. Though the pins will probably last much longer than a single season during the harshest conditions we strongly recommend they be replaced as part of an annual maintenance procedure. Reduced price pin replacement only kits are available to all previous customers.
Features
  • Polyurethane Dust Boots
    Spiral Retaining Rings
    4 Way Sealing rings
    Installation Grease
    Aluminum Bronze Solid upper bushings
    Zerk fittings and Caps
    Zinc Plated Lower Plates
    Heavy Duty Lower Springs
    Hardened Chromolly 19mm GCK Ball Pins
    10.9 Grade Pinch Bolts
    5 min. Qucik Set Epoxy
  • 2 year parts replacement warantee
  • Rebuilds 2 Ball Joints

Share your knowledge of this product with other customers... Be the first to write a review

Browse for more products in the same category as this item:

944 85.5 & Up (Late) and 968 > Suspension
944 85.5 & Up (Late) and 968 > Suspension > Control Arms
944 85.5 & Up (Late) and 968 > Suspension > Suspension Bushings and Hardware
944 85.5 & Up (Late) and 968


Door Lock Mechanism - Right $235.26
Pagid Race Pad Set - 2905R01 Track Day Compound $129.52
Starter - Rebuilt - Bosch $255.79
Swepco 202 - Moly XP 75W90 Synthetic Transmission Oil $121.95 UPS Ground or 3 Day Shipping Only
Pagid Race Pad Set - 8101 $657.01
GiroDisc Slotted - Audi C7 RS6, RS7 Front Rotors
Hood Release Pull Handle Cover #42 on Illustration $18.88
Brake Pad Set - Rear $267.89
Camber Plates Set - Tarett Engineering $525.00