Knowledge Base:  
You are here: Knowledge Base > 924/944/968

Page of 3
Previous Page     Next Page
KLA Strut Brace Installation - 924S, 944, 968
944 STRUT BRACE INSTALL 1) Remove 4 nuts holding strut assembly to the body. 2) Place bracket over studs with brac
KLA Strut Brace Installation - 968/944 S2/944 S
1) Remove 4 nuts holding strut assembly to the body. 2) Place bracket over studs with bracket upright toward rear of car. 3) Replace washers
Koni Strut Conversion - 8641-1414S for late 944, 968
Author: Skip Koni sealed strut insert conversion (8641-1414S) Description Image Parts: Koni 8641-1414S Sport Struts - all conversion and instructions parts included. Tools: Aside
Motor Mount Replacement
Author: Skip Motor Mount Choices for the 944.Diagnosis: Motor mounts are designed to absorb vibration from the 944's water-cooled engine.  Here are some warning signs that yours may need t
Odometer Gear Replacement - late 944
Author: Skip Instructions: Remove 9 screws holding front/back together: Remove 4 screws holding speedometer in housing: Gently pull off speedometer needle and remove 2 screws holding face o
Oil Cooling, Auxiliary
  KISS ENGINEERING OIL COOLER KITS 944/944 TURBO TEST DATA AND INFORMATION    COOLER              &nb
Oil Pressure Relief Valve
 944 Oil Pressure Relief ValveBackground: Within the 944 series cars, the oil pressure is regulated by both speed of the engine as the engine drives the oil pump, and by a pressure valve. 
Oil Pressure Sending Unit Replacement
 Oil Sender Unit for 928/944/968/964/993The oil pressure sending unit is located just under the oil filter,underneath the car in the front area on the passenger side.  Jack car up on lift
Porsche Chronology
Some model history that may help with shopping our site  Model  Year  Engine  Note  356  55-65      911  65-69  2.0  
Rear Ride Height Adjustment
Porsche 924/944/968 rear ride height can be lowered (in most cases) by approximately ¾" using the following procedure. This adjustment was originally designed for factory ride height settings across t
Rear Spring Rates vs. Effective Rates
An effective spring rate is the value when taking into consideration the placement, construction, and type of the sprung materials. Torsion bar diameter is expressed as the effective diameter. 
Rear Sway Bar Installation
This procedure is specifically for the installation of a 968 M030 Sway Bar but also applies to any 924/944/968 factory sway bar. The best (easiest) way to remove or install the sway bar is with t
Rear Wheel Bearing Diagnosis
  Diagnosis:    Name that tune... 'wuh wuh wuh wuh', as you go around a corner?  Rhythmic rubbing sounds from the rear of the car, especially during cornering, is usually the
Rear Wheel Bearing Replacement - 924, early 944
 Parts needed:Rear Wheel Bearing KitStub Axel Nut/Rear Wheel Bearing NutMoly GreaseProcedure: Lift rear or entire vehicle SAFELY! Release handbrake Remove the rear wheels. Remove the rea
Rear Wheel Bearing Replacement - late 944, 968
  Discussion:   This procedure will describe the removal and subsequent installation of rear wheel bearings on a Porsche 944 with aluminum trailing arms (1985.5 & later). 
Ride Height Measurement
Torsion Bar Indexing 101 The outside has 44 splines (teeth) Every tooth you move the outside splines you move the spring plate about 9 degrees. The inside has 40 splines (teeth) Every tooth
Rod Bearing Replacement
  Discussion: This procedure will detail the steps necessary to replace the Rod Bearings on a 944 Turbo car.  With some modifications it may also be applied to normally aspirated 944 cars
Seat Back Brace Installation Instructions
Seat Back Brace Installation Instructions To Order the I/O Port Seat Back Brace SBB-15 Click Here.Determine where on the seat back the mount needs to be to have the 1½” tubing within ±20° from horizon
Shift Lever Rebuild
  This is an alternate procedure This article is an alternate procedure for overhauling the shift lever.  Normally, replacement of parts with new would be ideal.  The parts needed
Short Shift Kit
  Procedure: Raise care on lift or place on jack stands.  Make sure car is safely and securely supported, and you have plenty of room to see around the transaxle. Locate the shifter